Packages and Binaries:

openvpn

OpenVPN is an application to securely tunnel IP networks over a single UDP or TCP port. It can be used to access remote sites, make secure point-to-point connections, enhance wireless security, etc.

OpenVPN uses all of the encryption, authentication, and certification features provided by the OpenSSL library (any cipher, key size, or HMAC digest).

OpenVPN may use static, pre-shared keys or TLS-based dynamic key exchange. It also supports VPNs with dynamic endpoints (DHCP or dial-up clients), tunnels over NAT or connection-oriented stateful firewalls (such as Linux’s iptables).

Installed size: 1.72 MB
How to install: sudo apt install openvpn

Dependencies:
  • debconf | debconf-2.0
  • libc6
  • libcap-ng0
  • liblz4-1
  • liblzo2-2
  • libnl-3-200
  • libnl-genl-3-200
  • libpam0g
  • libpkcs11-helper1
  • libssl3
  • libsystemd0
openvpn

Secure IP tunnel daemon

root@kali:~# openvpn --help
OpenVPN 2.6.7 x86_64-pc-linux-gnu [SSL (OpenSSL)] [LZO] [LZ4] [EPOLL] [PKCS11] [MH/PKTINFO] [AEAD] [DCO]

General Options:
--config file   : Read configuration options from file.
--help          : Show options.
--version       : Show copyright and version information.

Tunnel Options:
--local host    : Local host name or ip address. Implies --bind.
--remote host [port] : Remote host name or ip address.
--remote-random : If multiple --remote options specified, choose one randomly.
--remote-random-hostname : Add a random string to remote DNS name.
--mode m        : Major mode, m = 'p2p' (default, point-to-point) or 'server'.
--proto p       : Use protocol p for communicating with peer.
                  p = udp (default), tcp-server, tcp-client
                      udp4, tcp4-server, tcp4-client
                      udp6, tcp6-server, tcp6-client
--proto-force p : only consider protocol p in list of connection profiles.
                  p = udp or tcp
--connect-retry n [m] : For client, number of seconds to wait between
                  connection retries (default=1). On repeated retries
                  the wait time is exponentially increased to a maximum of m
                  (default=300).
--connect-retry-max n : Maximum connection attempt retries, default infinite.
--http-proxy s p [up] [auth] : Connect to remote host
                  through an HTTP proxy at address s and port p.
                  If proxy authentication is required,
                  up is a file containing username/password on 2 lines, or
                  'stdin' to prompt from console.  Add auth='ntlm' if
                  the proxy requires NTLM authentication.
--http-proxy s p 'auto[-nct]' : Like the above directive, but automatically
                  determine auth method and query for username/password
                  if needed.  auto-nct disables weak proxy auth methods.
--http-proxy-option type [parm] : Set extended HTTP proxy options.
                                  Repeat to set multiple options.
                  VERSION version (default=1.0)
                  AGENT user-agent
--socks-proxy s [p] [up] : Connect to remote host through a Socks5 proxy at
                  address s and port p (default port = 1080).
                  If proxy authentication is required,
                  up is a file containing username/password on 2 lines, or
                  'stdin' to prompt for console.
--socks-proxy-retry : Retry indefinitely on Socks proxy errors.
--resolv-retry n: If hostname resolve fails for --remote, retry
                  resolve for n seconds before failing (disabled by default).
                  Set n="infinite" to retry indefinitely.
--float         : Allow remote to change its IP address/port, such as through
                  DHCP (this is the default if --remote is not used).
--ipchange cmd  : Run command cmd on remote ip address initial
                  setting or change -- execute as: cmd ip-address port#
--port port     : TCP/UDP port # for both local and remote.
--lport port    : TCP/UDP port # for local (default=1194). Implies --bind.
--rport port    : TCP/UDP port # for remote (default=1194).
--bind          : Bind to local address and port. (This is the default unless
                  --proto tcp-client or --http-proxy or --socks-proxy is used).
--nobind        : Do not bind to local address and port.
--dev tunX|tapX : tun/tap device (X can be omitted for dynamic device.
--dev-type dt   : Which device type are we using? (dt = tun or tap) Use
                  this option only if the tun/tap device used with --dev
                  does not begin with "tun" or "tap".
--dev-node node : Explicitly set the device node rather than using
                  /dev/net/tun, /dev/tun, /dev/tap, etc.
--disable-dco   : Do not attempt using Data Channel Offload.
--lladdr hw     : Set the link layer address of the tap device.
--topology t    : Set --dev tun topology: 'net30', 'p2p', or 'subnet'.
--ifconfig l rn : TUN: configure device to use IP address l as a local
                  endpoint and rn as a remote endpoint.  l & rn should be
                  swapped on the other peer.  l & rn must be private
                  addresses outside of the subnets used by either peer.
                  TAP: configure device to use IP address l as a local
                  endpoint and rn as a subnet mask.
--ifconfig-ipv6 l r : configure device to use IPv6 address l as local
                      endpoint (as a /64) and r as remote endpoint
--ifconfig-noexec : Don't actually execute ifconfig/netsh command, instead
                    pass --ifconfig parms by environment to scripts.
--ifconfig-nowarn : Don't warn if the --ifconfig option on this side of the
                    connection doesn't match the remote side.
--route network [netmask] [gateway] [metric] :
                  Add route to routing table after connection
                  is established.  Multiple routes can be specified.
                  netmask default: 255.255.255.255
                  gateway default: taken from --route-gateway or --ifconfig
                  Specify default by leaving blank or setting to "default".
--route-ipv6 network/bits [gateway] [metric] :
                  Add IPv6 route to routing table after connection
                  is established.  Multiple routes can be specified.
                  gateway default: taken from --route-ipv6-gateway or 'remote'
                  in --ifconfig-ipv6
--route-gateway gw|'dhcp' : Specify a default gateway for use with --route.
--route-ipv6-gateway gw : Specify a default gateway for use with --route-ipv6.
--route-metric m : Specify a default metric for use with --route.
--route-delay n [w] : Delay n seconds after connection initiation before
                  adding routes (may be 0).  If not specified, routes will
                  be added immediately after tun/tap open.  On Windows, wait
                  up to w seconds for TUN/TAP adapter to come up.
--route-up cmd  : Run command cmd after routes are added.
--route-pre-down cmd : Run command cmd before routes are removed.
--route-noexec  : Don't add routes automatically.  Instead pass routes to
                  --route-up script using environmental variables.
--route-nopull  : When used with --client or --pull, accept options pushed
                  by server EXCEPT for routes, dns, and dhcp options.
--allow-pull-fqdn : Allow client to pull DNS names from server for
                    --ifconfig, --route, and --route-gateway.
--redirect-gateway [flags]: Automatically execute routing
                  commands to redirect all outgoing IP traffic through the
                  VPN.  Add 'local' flag if both OpenVPN servers are directly
                  connected via a common subnet, such as with WiFi.
                  Add 'def1' flag to set default route using using 0.0.0.0/1
                  and 128.0.0.0/1 rather than 0.0.0.0/0.  Add 'bypass-dhcp'
                  flag to add a direct route to DHCP server, bypassing tunnel.
                  Add 'bypass-dns' flag to similarly bypass tunnel for DNS.
--redirect-private [flags]: Like --redirect-gateway, but omit actually changing
                  the default gateway.  Useful when pushing private subnets.
--block-ipv6     : (Client) Instead sending IPv6 to the server generate
                   ICMPv6 host unreachable messages on the client.
                   (Server) Instead of forwarding IPv6 packets send
                   ICMPv6 host unreachable packets to the client.
--client-nat snat|dnat network netmask alias : on client add 1-to-1 NAT rule.
--push-peer-info : (client only) push client info to server.
--setenv name value : Set a custom environmental variable to pass to script.
--setenv FORWARD_COMPATIBLE 1 : Relax config file syntax checking to allow
                  directives for future OpenVPN versions to be ignored.
--ignore-unknown-option opt1 opt2 ...: Relax config file syntax. Allow
                  these options to be ignored when unknown
--script-security level: Where level can be:
                  0 -- strictly no calling of external programs
                  1 -- (default) only call built-ins such as ifconfig
                  2 -- allow calling of built-ins and scripts
                  3 -- allow password to be passed to scripts via env
--shaper n      : Restrict output to peer to n bytes per second.
--keepalive n m : Helper option for setting timeouts in server mode.  Send
                  ping once every n seconds, restart if ping not received
                  for m seconds.
--inactive n [bytes] : Exit after n seconds of activity on tun/tap device
                  produces a combined in/out byte count < bytes.
--session-timeout n: Limit connection time to n seconds.
--ping-exit n   : Exit if n seconds pass without reception of remote ping.
--ping-restart n: Restart if n seconds pass without reception of remote ping.
--ping-timer-rem: Run the --ping-exit/--ping-restart timer only if we have a
                  remote address.
--ping n        : Ping remote once every n seconds over TCP/UDP port.
--multihome     : Configure a multi-homed UDP server.
--fast-io       : (experimental) Optimize TUN/TAP/UDP writes.
--remap-usr1 s  : On SIGUSR1 signals, remap signal (s='SIGHUP' or 'SIGTERM').
--persist-tun   : Keep tun/tap device open across SIGUSR1 or --ping-restart.
--persist-remote-ip : Keep remote IP address across SIGUSR1 or --ping-restart.
--persist-local-ip  : Keep local IP address across SIGUSR1 or --ping-restart.
--persist-key   : Don't re-read key files across SIGUSR1 or --ping-restart.
--passtos       : TOS passthrough (applies to IPv4 only).
--tun-mtu n     : Take the tun/tap device MTU to be n and derive the
                  TCP/UDP MTU from it (default=1500).
--tun-mtu-extra n : Assume that tun/tap device might return as many
                  as n bytes more than the tun-mtu size on read
                  (default TUN=0 TAP=32).
--link-mtu n    : Take the TCP/UDP device MTU to be n and derive the tun MTU
                  from it.
--mtu-disc type : Should we do Path MTU discovery on TCP/UDP channel?
                  'no'    -- Never send DF (Don't Fragment) frames
                  'maybe' -- Use per-route hints
                  'yes'   -- Always DF (Don't Fragment)
--mtu-test      : Empirically measure and report MTU.
--fragment max  : Enable internal datagram fragmentation so that no UDP
                  datagrams are sent which are larger than max bytes.
                  Adds 4 bytes of overhead per datagram.
--mssfix [n]    : Set upper bound on TCP MSS, default = tun-mtu size
                  or --fragment max value, whichever is lower.
--sndbuf size   : Set the TCP/UDP send buffer size.
--rcvbuf size   : Set the TCP/UDP receive buffer size.
--mark value    : Mark encrypted packets being sent with value. The mark value
                  can be matched in policy routing and packetfilter rules.
--bind-dev dev  : Bind to the given device when making connection to a peer or
                  listening for connections. This allows sending encrypted packets
                  via a VRF present on the system.
--txqueuelen n  : Set the tun/tap TX queue length to n (Linux only).
--memstats file : Write live usage stats to memory mapped binary file.
--mlock         : Disable Paging -- ensures key material and tunnel
                  data will never be written to disk.
--up cmd        : Run command cmd after successful tun device open.
                  Execute as: cmd tun/tap-dev tun-mtu link-mtu \
                              ifconfig-local-ip ifconfig-remote-ip
                  (pre --user or --group UID/GID change)
--up-delay      : Delay tun/tap open and possible --up script execution
                  until after TCP/UDP connection establishment with peer.
--down cmd      : Run command cmd after tun device close.
                  (post --user/--group UID/GID change and/or --chroot)
                  (command parameters are same as --up option)
--down-pre      : Run --down command before TUN/TAP close.
--up-restart    : Run up/down commands for all restarts including those
                  caused by --ping-restart or SIGUSR1
--user user     : Set UID to user after initialization.
--group group   : Set GID to group after initialization.
--chroot dir    : Chroot to this directory after initialization.
--cd dir        : Change to this directory before initialization.
--daemon [name] : Become a daemon after initialization.
                  The optional 'name' parameter will be passed
                  as the program name to the system logger.
--syslog [name] : Output to syslog, but do not become a daemon.
                  See --daemon above for a description of the 'name' parm.
--log file      : Output log to file which is created/truncated on open.
--log-append file : Append log to file, or create file if nonexistent.
--suppress-timestamps : Don't log timestamps to stdout/stderr.
--machine-readable-output : Always log timestamp, message flags to stdout/stderr.
--writepid file : Write main process ID to file.
--nice n        : Change process priority (>0 = lower, <0 = higher).
--echo [parms ...] : Echo parameters to log output.
--verb n        : Set output verbosity to n (default=1):
                  (Level 3 is recommended if you want a good summary
                  of what's happening without being swamped by output).
                : 0 -- no output except fatal errors
                : 1 -- startup info + connection initiated messages +
                       non-fatal encryption & net errors
                : 2,3 -- show TLS negotiations & route info
                : 4 -- show parameters
                : 5 -- show 'RrWw' chars on console for each packet sent
                       and received from TCP/UDP (caps) or tun/tap (lc)
                : 6 to 11 -- debug messages of increasing verbosity
--mute n        : Log at most n consecutive messages in the same category.
--status file [n] : Write operational status to file every n seconds.
--status-version [n] : Choose the status file format version number.
                  Currently, n can be 1, 2, or 3 (default=1).
--disable-occ   : (DEPRECATED) Disable options consistency check between peers.
--gremlin mask  : Special stress testing mode (for debugging only).
--compress alg  : Use compression algorithm alg
--allow-compression: Specify whether compression should be allowed
--comp-lzo      : Use LZO compression -- may add up to 1 byte per
                  packet for incompressible data.
--comp-noadapt  : Don't use adaptive compression when --comp-lzo
                  is specified.
--management ip port [pass] : Enable a TCP server on ip:port to handle
                  management functions.  pass is a password file
                  or 'stdin' to prompt from console.
                  To listen on a unix domain socket, specific the pathname
                  in place of ip and use 'unix' as the port number.
--management-client : Management interface will connect as a TCP client to
                      ip/port rather than listen as a TCP server.
--management-query-passwords : Query management channel for private key
                  and auth-user-pass passwords.
--management-query-proxy : Query management channel for proxy information.
--management-query-remote : Query management channel for --remote directive.
--management-hold : Start OpenVPN in a hibernating state, until a client
                    of the management interface explicitly starts it.
--management-signal : Issue SIGUSR1 when management disconnect event occurs.
--management-forget-disconnect : Forget passwords when management disconnect
                                 event occurs.
--management-up-down : Report tunnel up/down events to management interface.
--management-log-cache n : Cache n lines of log file history for usage
                  by the management channel.
--management-client-user u  : When management interface is a unix socket, only
                              allow connections from user u.
--management-client-group g : When management interface is a unix socket, only
                              allow connections from group g.
--management-client-auth : gives management interface client the responsibility
                           to authenticate clients after their client certificate
			      has been verified.
--plugin m [str]: Load plug-in module m passing str as an argument
                  to its initialization function.
--vlan-tagging  : Enable 802.1Q-based VLAN tagging.
--vlan-accept tagged|untagged|all : Set VLAN tagging mode. Default is 'all'.
--vlan-pvid v   : Sets the Port VLAN Identifier. Defaults to 1.

Multi-Client Server options (when --mode server is used):
--server network netmask : Helper option to easily configure server mode.
--server-ipv6 network/bits : Configure IPv6 server mode.
--server-bridge [IP netmask pool-start-IP pool-end-IP] : Helper option to
                    easily configure ethernet bridging server mode.
--push "option" : Push a config file option back to the peer for remote
                  execution.  Peer must specify --pull in its config file.
--push-reset    : Don't inherit global push list for specific
                  client instance.
--push-remove opt : Remove options matching 'opt' from the push list for
                  a specific client instance.
--ifconfig-pool start-IP end-IP [netmask] : Set aside a pool of subnets
                  to be dynamically allocated to connecting clients.
--ifconfig-pool-persist file [seconds] : Persist/unpersist ifconfig-pool
                  data to file, at seconds intervals (default=600).
                  If seconds=0, file will be treated as read-only.
--ifconfig-ipv6-pool base-IP/bits : set aside an IPv6 network block
                  to be dynamically allocated to connecting clients.
--ifconfig-push local remote-netmask : Push an ifconfig option to remote,
                  overrides --ifconfig-pool dynamic allocation.
                  Only valid in a client-specific config file.
--ifconfig-ipv6-push local/bits remote : Push an ifconfig-ipv6 option to
                  remote, overrides --ifconfig-ipv6-pool allocation.
                  Only valid in a client-specific config file.
--iroute network [netmask] : Route subnet to client.
--iroute-ipv6 network/bits : Route IPv6 subnet to client.
                  Sets up internal routes only.
                  Only valid in a client-specific config file.
--disable       : Client is disabled.
                  Only valid in a client-specific config file.
--verify-client-cert [none|optional|require] : perform no, optional or
                  mandatory client certificate verification.
                  Default is to require the client to supply a certificate.
--username-as-common-name  : For auth-user-pass authentication, use
                  the authenticated username as the common name,
                  rather than the common name from the client cert.
--auth-user-pass-verify cmd method: Query client for username/password and
                  run command cmd to verify.  If method='via-env', pass
                  user/pass via environment, if method='via-file', pass
                  user/pass via temporary file.
--auth-gen-token  [lifetime] Generate a random authentication token which is pushed
                  to each client, replacing the password.  Useful when
                  OTP based two-factor auth mechanisms are in use and
                  --reneg-* options are enabled. Optionally a lifetime in seconds
                  for generated tokens can be set.
--opt-verify    : (DEPRECATED) Clients that connect with options that are incompatible
                  with those of the server will be disconnected.
--auth-user-pass-optional : Allow connections by clients that don't
                  specify a username/password.
--no-name-remapping : (DEPRECATED) Allow Common Name and X509 Subject to include
                      any printable character.
--client-to-client : Internally route client-to-client traffic.
--duplicate-cn  : Allow multiple clients with the same common name to
                  concurrently connect.
--client-connect cmd : Run command cmd on client connection.
--client-disconnect cmd : Run command cmd on client disconnection.
--client-config-dir dir : Directory for custom client config files.
--ccd-exclusive : Refuse connection unless custom client config is found.
--tmp-dir dir   : Temporary directory, used for --client-connect return file and plugin communication.
--hash-size r v : Set the size of the real address hash table to r and the
                  virtual address table to v.
--bcast-buffers n : Allocate n broadcast buffers.
--tcp-queue-limit n : Maximum number of queued TCP output packets.
--tcp-nodelay   : Macro that sets TCP_NODELAY socket flag on the server
                  as well as pushes it to connecting clients.
--learn-address cmd : Run command cmd to validate client virtual addresses.
--connect-freq n s : Allow a maximum of n new connections per s seconds.
--connect-freq-initial n s : Allow a maximum of n replies for initial connections attempts per s seconds.
--max-clients n : Allow a maximum of n simultaneously connected clients.
--max-routes-per-client n : Allow a maximum of n internal routes per client.
--stale-routes-check n [t] : Remove routes with a last activity timestamp
                             older than n seconds. Run this check every t
                             seconds (defaults to n).
--explicit-exit-notify [n] : In UDP server mode send [RESTART] command on exit/restart to connected
                             clients. n = 1 - reconnect to same server,
                             2 - advance to next server, default=1.
--port-share host port [dir] : When run in TCP mode, proxy incoming HTTPS
                  sessions to a web server at host:port.  dir specifies an
                  optional directory to write origin IP:port data.

Client options (when connecting to a multi-client server):
--client         : Helper option to easily configure client mode.
--auth-user-pass [up] : Authenticate with server using username/password.
                  up is a file containing the username on the first line,
                  and a password on the second. If either the password or both
                  the username and the password are omitted OpenVPN will prompt
                  for them from console.
--pull           : Accept certain config file options from the peer as if they
                  were part of the local config file.  Must be specified
                  when connecting to a '--mode server' remote host.
--pull-filter accept|ignore|reject t : Filter each option received from the
                  server if it starts with the text t. The action flag accept,
                  ignore or reject causes the option to be allowed, removed or
                  rejected with error. May be specified multiple times, and
                  each filter is applied in the order of appearance.
--dns server <n> <option> <value> [value ...] : Configure option for DNS server #n
                  Valid options are :
                  address <addr[:port]> [addr[:port] ...] : server addresses 4/6
                  resolve-domains <domain> [domain ...] : split domains
                  dnssec <yes|no|optional> : option to use DNSSEC
                  type <DoH|DoT> : query server over HTTPS / TLS
                  sni <domain> : DNS server name indication
--dns search-domains <domain> [domain ...]:
                  Add domains to DNS domain search list
--auth-retry t  : How to handle auth failures.  Set t to
                  none (default), interact, or nointeract.
--static-challenge t e : Enable static challenge/response protocol using
                  challenge text t, with e indicating echo flag (0|1)
--connect-timeout n : when polling possible remote servers to connect to
                  in a round-robin fashion, spend no more than n seconds
                  waiting for a response before trying the next server.
--allow-recursive-routing : When this option is set, OpenVPN will not drop
                  incoming tun packets with same destination as host.
--explicit-exit-notify [n] : On exit/restart, send exit signal to
                  server/remote. n = # of retries, default=1.

Data Channel Encryption Options (must be compatible between peers):
(These options are meaningful for both Static Key & TLS-mode)
--secret f [d]  : (DEPRECATED) Enable Static Key encryption mode (non-TLS).
                  Use shared secret file f, generate with --genkey.
                  The optional d parameter controls key directionality.
                  If d is specified, use separate keys for each
                  direction, set d=0 on one side of the connection,
                  and d=1 on the other side.
--auth alg      : Authenticate packets with HMAC using message
                  digest algorithm alg (default=SHA1).
                  (usually adds 16 or 20 bytes per packet)
                  Set alg=none to disable authentication.
--cipher alg    : Encrypt packets with cipher algorithm alg.
                  You should usually use --data-ciphers instead.
                  Set alg=none to disable encryption.
--data-ciphers list : List of ciphers that are allowed to be negotiated.
--engine [name] : Enable OpenSSL hardware crypto engine functionality.
--no-replay     : (DEPRECATED) Disable replay protection.
--mute-replay-warnings : Silence the output of replay warnings to log file.
--replay-window n [t]  : Use a replay protection sliding window of size n
                         and a time window of t seconds.
                         Default n=64 t=15
--replay-persist file : Persist replay-protection state across sessions
                  using file.
--test-crypto   : Run a self-test of crypto features enabled.
                  For debugging only.

TLS Key Negotiation Options:
(These options are meaningful only for TLS-mode)
--tls-server    : Enable TLS and assume server role during TLS handshake.
--tls-client    : Enable TLS and assume client role during TLS handshake.
--ca file       : Certificate authority file in .pem format containing
                  root certificate.
--capath dir    : A directory of trusted certificates (CAs and CRLs).
--dh file       : File containing Diffie Hellman parameters
                  in .pem format (for --tls-server only).
                  Use "openssl dhparam -out dh1024.pem 1024" to generate.
--cert file     : Local certificate in .pem format -- must be signed
                  by a Certificate Authority in --ca file.
--extra-certs file : one or more PEM certs that complete the cert chain.
--key file      : Local private key in .pem format.
--tls-version-min <version> ['or-highest'] : sets the minimum TLS version we
    will accept from the peer.  If version is unrecognized and 'or-highest'
    is specified, require max TLS version supported by SSL implementation.
--tls-version-max <version> : sets the maximum TLS version we will use.
--pkcs12 file   : PKCS#12 file containing local private key, local certificate
                  and optionally the root CA certificate.
--x509-username-field : Field in x509 certificate containing the username.
                        Default is CN in the Subject field.
--verify-hash hash [algo] : Specify fingerprint for level-1 certificate.
                            Valid algo flags are SHA1 and SHA256. 
--tls-cipher l  : A list l of allowable TLS ciphers separated by : (optional).
--tls-ciphersuites l: A list of allowed TLS 1.3 cipher suites separated by : (optional)
                : Use --show-tls to see a list of supported TLS ciphers (suites).
--tls-cert-profile p : Set the allowed certificate crypto algorithm profile
                  (default=legacy).
--providers l   : A list l of OpenSSL providers to load.
--tls-timeout n : Packet retransmit timeout on TLS control channel
                  if no ACK from remote within n seconds (default=2).
--reneg-bytes n : Renegotiate data chan. key after n bytes sent and recvd.
--reneg-pkts n  : Renegotiate data chan. key after n packets sent and recvd.
--reneg-sec max [min] : Renegotiate data chan. key after at most max (default=3600)
                  and at least min (defaults to 90% of max on servers and equal
                  to max on clients).
--hand-window n : Data channel key exchange must finalize within n seconds
                  of handshake initiation by any peer (default=60).
--tran-window n : Transition window -- old key can live this many seconds
                  after new key renegotiation begins (default=3600).
--single-session: Allow only one session (reset state on restart).
--tls-exit      : Exit on TLS negotiation failure.
--tls-auth f [d]: Add an additional layer of authentication on top of the TLS
                  control channel to protect against attacks on the TLS stack
                  and DoS attacks.
                  f (required) is a shared-secret key file.
                  The optional d parameter controls key directionality,
                  see --secret option for more info.
--tls-crypt key : Add an additional layer of authenticated encryption on top
                  of the TLS control channel to hide the TLS certificate,
                  provide basic post-quantum security and protect against
                  attacks on the TLS stack and DoS attacks.
                  key (required) provides the pre-shared key file.
                  see --secret option for more info.
--tls-crypt-v2 key : For clients: use key as a client-specific tls-crypt key.
                  For servers: use key to decrypt client-specific keys.  For
                  key generation (--genkey tls-crypt-v2-client): use key to
                  encrypt generated client-specific key.  (See --tls-crypt.)
--genkey tls-crypt-v2-client [keyfile] [base64 metadata]: Generate a
                  fresh tls-crypt-v2 client key, and store to
                  keyfile.  If supplied, include metadata in wrapped key.
--genkey tls-crypt-v2-server [keyfile] [base64 metadata]: Generate a
                  fresh tls-crypt-v2 server key, and store to keyfile
--tls-crypt-v2-verify cmd : Run command cmd to verify the metadata of the
                  client-supplied tls-crypt-v2 client key
--askpass [file]: Get PEM password from controlling tty before we daemonize.
--auth-nocache  : Don't cache --askpass or --auth-user-pass passwords.
--crl-verify crl ['dir']: Check peer certificate against a CRL.
--tls-verify cmd: Run command cmd to verify the X509 name of a
                  pending TLS connection that has otherwise passed all other
                  tests of certification.  cmd should return 0 to allow
                  TLS handshake to proceed, or 1 to fail.  (cmd is
                  executed as 'cmd certificate_depth subject')
--tls-export-cert [directory] : Get peer cert in PEM format and store it 
                  in an openvpn temporary file in [directory]. Peer cert is 
                  stored before tls-verify script execution and deleted after.
--verify-x509-name name: Accept connections only from a host with X509 subject
                  DN name. The remote host must also pass all other tests
                  of verification.
--ns-cert-type t: (DEPRECATED) Require that peer certificate was signed with 
                  an explicit nsCertType designation t = 'client' | 'server'.
--x509-track x  : Save peer X509 attribute x in environment for use by
                  plugins and management interface.
--keying-material-exporter label len : Save Exported Keying Material (RFC5705)
                  of len bytes (min. 16 bytes) using label in environment for use by plugins.
--remote-cert-ku v ... : Require that the peer certificate was signed with
                  explicit key usage, you can specify more than one value.
                  value should be given in hex format.
--remote-cert-eku oid : Require that the peer certificate was signed with
                  explicit extended key usage. Extended key usage can be encoded
                  as an object identifier or OpenSSL string representation.
--remote-cert-tls t: Require that peer certificate was signed with explicit
                  key usage and extended key usage based on RFC3280 TLS rules.
                  t = 'client' | 'server'.

PKCS#11 Options:
--pkcs11-providers provider ... : PKCS#11 provider to load.
--pkcs11-protected-authentication [0|1] ... : Use PKCS#11 protected authentication
                              path. Set for each provider.
--pkcs11-private-mode hex ...   : PKCS#11 private key mode mask.
                              0       : Try  to determine automatically (default).
                              1       : Use Sign.
                              2       : Use SignRecover.
                              4       : Use Decrypt.
                              8       : Use Unwrap.
--pkcs11-cert-private [0|1] ... : Set if login should be performed before
                                  certificate can be accessed. Set for each provider.
--pkcs11-pin-cache seconds      : Number of seconds to cache PIN. The default is -1
                                  cache until token is removed.
--pkcs11-id-management          : Acquire identity from management interface.
--pkcs11-id serialized-id 'id'  : Identity to use, get using standalone --show-pkcs11-ids

SSL Library information:
--show-ciphers  : Show cipher algorithms to use with --cipher option.
--show-digests  : Show message digest algorithms to use with --auth option.
--show-engines  : Show hardware crypto accelerator engines (if available).
--show-tls      : Show all TLS ciphers (TLS used only as a control channel).

Generate a new key :
--genkey secret file   : Generate a new random key of type and write to file
                         (for use with --secret, --tls-auth or --tls-crypt).
Tun/tap config mode (available with linux 2.4+):
--mktun         : Create a persistent tunnel.
--rmtun         : Remove a persistent tunnel.
--dev tunX|tapX : tun/tap device
--dev-type dt   : Device type.  See tunnel options above for details.
--user user     : User to set privilege to.
--group group   : Group to set privilege to.

PKCS#11 standalone options:
--show-pkcs11-ids [provider] [cert_private] : Show PKCS#11 available ids.
                                            --verb option can be added *BEFORE* this.

General Standalone Options:
--show-gateway : Show info about default gateway.

Updated on: 2023-Nov-20